- Contact Us
This NuAire In-VitroCell™ direct-heat CO2 incubator delivers a reliable, controlled in-vitro environment for the optimum growth of tissue cell cultures and other organisms. It provides a sterile chamber with constant temperature, constant CO2 level, and precise humidity.
The easy-to-use NuTouch ECS has a 5x7-inch (127 x 178 mm) LCD screen that gives a clear view of operating control parameters and status indicators, and an embedded touch panel for data entry. It lets operators program and calibrate optimum conditions for culture growth, and the ECS automatically makes adjustments to the growth chamber, maintaining ideal growth conditions.
The direct-heat CO2 incubator accurately measures the percentage of carbon dioxide gas using a dual-wave infrared (IR) sensor. The measurement is accurate within ±0.1 percent and is insensitive to other components, such as water vapor.
The CO2 level and temperature recover automatically in approximately five minutes after a one-minute door opening. Humidity recovers to 90 percent of original level 20-40 minutes after a 15-second door opening.
Dual sterilization cycles (95°C humidified or 145°C dry) help control contamination when switching cell lines.
The CO2 incubator has a closed-loop HEPA filtration system, similar to an ISO Class 5 clean room. A continuously operating air pump maintains positive pressure as gas and air pass through the 99.99 percent efficient filters.
The interior of the direct-heat incubator is constructed of 16-gauge steel and is crevice-free and cove-cornered. This design, coupled with the fact that the highly polished stainless steel surface inhibits biological growth and is easily cleaned, helps prevent contamination. The inner shelves and rails are easy to remove for sterilization.
Because the NU-5720 is constructed with few moving parts, there is almost no vibration to disturb cell lines.
The side, bottom, top and back walls of the chamber have foil heating elements and an individual door heater provide a stable temperature accurate within ±0.3°C. Temperature is monitored using dual-temperature sensor probes. Also, two fans mounted on the bottom cover panel run continuously for accurate chamber temperature control over a 60-85°F ambient temperature range.
Proper humidity levels up to 95% percent are maintained in the CO2 incubator chamber through water evaporation from a stainless steel three-liter reservoir. A sensor monitors humidity, and water vapor is injected to meet the set point.
|Exterior Dimensions (W x D x H)||
26.75 x 27.12 x 41.5 in.
679.5 x 689 x 1054 mm
|Foot Print (W x D)||
23.75 x 20.75 in.
603.2 x 527.1 mm
|Interior Dimensions (W x D x H)||
21.5 x 21 x 26.5 in.
546.1 x 533.4 x 673.1 mm
5° above ambient (to a 30° max ambient) to 55°
|Set-Point Range:||5°C to 55°C (37.0 Default)|
|Uniformity:||±0.35°C @ 37°C|
|Recovery:||0.12°C/min. on Average|
|Door and Perimeter Heater Control Logic:||Base Duty Cycle set to chamber temperature Set-Point Proportional 0-100% [manually adjustable]|
|Temperature Sensor Type:||Precision Integrated Circuit|
CO2 Control Standard
0.1 to 20% 5% Default Set Point
|CO2 Recovery:||Up to 5% ±0.2% / -0.5 in 5 minutes Average|
|CO2 Display Resolution:||0.1%|
|CO2 Control Logic:||Fixed Algorithm/Manual, Environmental Adaptable|
|CO2 Sensor Type:||Infrared (NDIR)|
Relative Humidity Display and Control
Ambient dependent to 90%
|RH Recovery:||90% +5%/-3% within 25 minutes on average|
|RH Control Logic:||Fixed algorithm/manual environmental adaptable|
|RH Sensor Type:||Precision capacitance bulk-polymer|
E: 230V, 50/60Hz
|Start Up Ower||475 Watts|
|Running Power||250 Watts|
|Sterilization Cycle||750 Watts|